ā† Back to Appliance Medic

Bosch Washing-Machine

24 manual(s) 95 error code(s) 10 guide(s)

šŸ“– Service Manuals

Also covers: typevariants

āš” Bosch Error Codes

E01
Water supply issue ā€” inlet valve not opening or water pressure too low
E02
Heater electronics fault detected in self-test
E05
Door sensor circuit fault
E07
Internal heater fault
E10
Water leakage detected ā€” float switch activated
E21
Heat pump motor circuit fault at control board
E23
Drain issue ā€” water not draining properly
E25
Drain pump blocked or cover loose
E27
Heat pump motor circuit fault
E0103
Main control board relay fault
E0105
Wash arm diverter circuit fault in control board
E0107
Main control board relay fault
E0110
Heat pump internal heater fault
E2060
Drain issue ā€” pump blocked or hose restricted
E6103
Drain pump blocked or cover loose
E6160
Drain pump blocked ā€” debris in pump or hose
E03
There is a main control board relay fault/error. Reset power to breaker for 30 seconds. If not resol
E04
Appliance has detected faulty (heater) electronics in the self-test. Contact Bosch Customer Support
E06
There is a door sensor circuit fault/error. Reset power to breaker for 30 seconds. If not resolved,
E09
There is a heat pump internal heater fault/error. Reset power to breaker for 30 seconds. If not reso

+75 more codes ā€” view all

šŸ“‹ washer Troubleshooting Guides

Washer not spinning

Lid switch failed, drive belt broken, drain pump blocked (won't spin if full of water), motor coupler failed, control bo...

Washer not filling with water

Water inlet valve failed, water supply valves closed, inlet hoses kinked, pressure switch failed, control board issue...

Washer leaking water

Door boot seal failed, drain hose connection loose, water inlet hose connection loose, tub crack, pump hose disconnected...

Washer shaking or walking during spin

Unbalanced load, leveling feet not adjusted, suspension springs failed, shock absorbers worn, spider arm broken (HE wash...

Washer draining slowly or not at all

Drain pump filter clogged, drain hose kinked, drain pump impeller blocked, standpipe clogged, check valve failed...

Washer making loud noise during spin

Tub bearings worn, spider arm broken (HE), transmission gears worn, drive belt slipping, foreign object in tub...

Washer error code UE / Ub (unbalanced)

Single heavy item (comforter, rug), suspension springs worn, shock absorbers failed, load too small...

Washer not agitating

Lid switch failure, broken drive belt, worn transmission coupler, motor relay failure...

Washer will not start

Power supply issue, lid switch failure, control lock enabled, defective control board...

Washer fills but does not drain

Clogged drain pump filter, kinked drain hose, faulty drain pump, clogged drain line...

āš™ļø Component Test Values

motor (submersible pump)

Normal: 2000000.0ā€“2000000.0Ī© Submersible pump ~2MĪ©

heating element (washer heating element)

Normal: 10.0ā€“30.0Ī© Washer water heating element

motor (washer agitator motor)

Normal: 2.0ā€“20.0Ī© Washer agitator motor

motor (washer spin motor)

Normal: 2.0ā€“10.0Ī© Washer spin motor

switch (door lock)

Normal: 70.0ā€“120.0Ī© Washer door lock solenoid

switch (lid switch)

Normal: 0.0ā€“1.0Ī© Lid switch - 0Ī© when closed

water inlet valve (washer inlet)

Normal: 500.0ā€“1500.0Ī© Washer water inlet valve coil

motor (direct drive agitator)

Normal: 2.0ā€“20.0Ī© Direct drive agitator coil

motor (direct drive spin)

Normal: 2.0ā€“10.0Ī© Direct drive spin coil

thermistor (washer water temp)

Normal: 4000.0ā€“8000.0Ī© Washer water temperature sensor at room temp

ā† Appliance Medic Ā· Search all manuals